Concrete cutting in Kalispell MT - straight lines right where you want them
Need an opening, a pipe trench or a broken section out of a slab or wall? We cut it straight and keep the dust down.
- Scanned before sawing We check structural slabs and walls for rebar and pipes first.
- Water on the blade Keeping the blade wet holds the dust down while we cut.
- Cut lines agreed together We settle every cut line with you before the saw starts.
- Cleanup settled up front You know how the wet cutting mess gets cleaned up beforehand.
- Licensed and insured.
- Free in-person estimates.
- Replies within 1 business day.
When does your concrete need cutting?
Most cutting calls start with something you need to get through or under, and a clean cut done early keeps a small opening from turning into a torn-up slab.
A leak or drain under the floor
A leak or new drain under the basement floor means opening the slab, and a leak left alone keeps washing out the base. A narrow cut opens only what's needed.
A basement wall needs an opening
A door or bigger window in a foundation wall means cutting through steel. Sawing after a scan keeps the wall around it sound, while a jackhammer tends to crack it.
One broken driveway section
When one panel of a driveway or patio has broken or sunk, cutting straight lines lets it come out alone. Wait, and it can take the next panel with it.
Adding on to an old slab
Pouring a new patio or wider driveway against the old one goes best off a straight saw cut. Butting new concrete against a ragged break leaves a weak, uneven seam.
A pipe or vent through concrete
A vent, drain or wire through a wall needs a round hole cut with a hollow core bit. A clean edge seals tight, and a chipped one lets water in.
Cracks wandering across new concrete
Control joints are shallow cuts that tell a slab where to crack. Skip them or saw them late on a new pour, and the slab picks its own crooked lines.
How we handle concrete cutting in Kalispell
Concrete cutting in Kalispell is mostly sawing straight lines through a slab or wall, or drilling round holes, so you get an opening, a pipe trench or a section that can come out without busting up the rest. We start by looking at what we're cutting and how thick it is, because that picks the saw. On structural slabs and walls we scan for rebar, the steel rods that hold concrete together, and for pipes before the blade goes in, since hitting either is a much bigger problem than the cut itself. We agree with you on exactly where the cuts go and how the slurry, the gray paste of water and concrete dust, gets cleaned up, and then we cut with water running on the blade, because concrete dust carries silica and a wet blade holds a lot of it down. Your price moves with the thickness, the steel and whether the pieces get hauled off, and the schedule mostly waits on the scan and the permit check, so my written estimate is where you'll see your own numbers.
Cutting is often the first step of something bigger. When a broken or sunken piece of driveway comes out, I look hard at the base, the packed gravel and soil the slab sits on, because a sunken section usually means the base under it settled, and a new piece poured on the same bad base just repeats the problem. If the budget's tight, I'd spend it on the base before the finish, since the finish is what you see and the base is what holds, and we pour the replacement as part of our concrete driveway building work. A straight cut on an old slab edge is also how we tie in new work for concrete patio construction.
What happens when you call us about concrete cutting in Kalispell?
From your first call to the last of the cleanup, here's who does what and what you'll have in hand before any saw starts.
Call or send a request
Call (406) 309-7887 or send the form, and tell us where the cut goes. I'll set a time to come out and look.
Measure and write it up
I measure the cuts with you, check how thick the concrete is and whether there's steel in it, then send a written estimate.
Check the office, then cut
Once you're ready, we find out which office covers your address and what it asks for, then set a date and do the cutting.
Clean up and walk the cuts
We clean up the slurry the way we agreed and walk the cuts with you, so you see the edges before we pack up.
Why Kalispell homeowners call Trueline Kalispell Concrete
The one who prices it stays
I look at the job and write the estimate, then stay on site while our own crew makes the cuts.
Running this business since 2017
I started this business in 2017 after years on other crews, and before that I patched barn floors on our family farm.
Covered before the saw starts
We're licensed and insured. Montana requires an independent contractor to carry Montana workers' comp or the state's exemption certificate.
Start with a look on site
Call (406) 309-7887 or use the estimate form, and I'll come walk the cut lines with you.
Get a written estimate for your concrete cut
Tell us if it's a slab or a wall, where the cut goes, roughly how long, and whether the pieces need hauling. We reply within one business day, and I come out for a free estimate on site, no obligation.
Saw cuts and core holes
Scroll through these examples of saw cuts, wall openings and core drilled holes to see what clean edges in concrete look like.
Questions about cutting concrete
These are the questions Kalispell homeowners ask most about cutting slabs and walls. If yours isn't here, give us a call and ask about your own job.
How much does concrete cutting cost in Kalispell?
Concrete saw cutting across the US usually runs about $4 to $25 per linear foot, and that's for the sawing, with removal as its own cost. Reinforced or thicker slabs cost more per foot to cut than thin ones, and on a small job a minimum charge can set the price more than the footage does. I'll measure yours and put it in a written estimate.
Does the price of concrete cutting include hauling the pieces away?
Not always, because sawing concrete and removing it are separate jobs, and some cutters leave the cut panels lying where they are. Breaking, hauling and disposal can cost more than the sawing itself, so ask whether a quote includes them. Ours says plainly which parts we're doing.
Why do contractors scan concrete before cutting it?
Scanning finds what's buried in a structural slab or wall, like rebar, pipes, conduit and post-tension cables, the steel cables stretched tight inside some slabs, so the blade misses them. It takes time before the cut, so plan for it on structural work. A blank scan only means nothing was found, so ask the crew what a clear result tells you about that spot.
What is the best way to cut concrete for a doorway or a pipe hole?
The best way is to match the saw to the surface: a flat saw for floors and driveways, a wall saw that rides a track for walls, a hand saw for tight corners and a wire saw for very thick or heavily reinforced sections. Round holes for pipes and vents are core drilled and priced apart from straight saw cuts.
Do I need a permit to cut concrete in Kalispell?
The city's permit list doesn't settle it, because it names building, plumbing, electrical and mechanical work and not concrete cutting. Inside city limits the Kalispell Building Department inspects all projects, so that's the office to ask, and outside city limits a county program or the state Building Codes Program may cover your address instead. Before we set a date we find out which office covers you, and we take care of the permits for our part of the job when one is needed.
How long does a concrete cutting job take?
The sawing is usually the quick part, and most of the wait comes before and after it. A structural slab or wall needs a scan first, the permit check has to be settled, and breaking and hauling adds time if the pieces are coming out. I'll walk you through the order when I write the estimate.
Talk to us about your concrete cutting job
If a plumber or builder is waiting on the opening, calling now gets the scan, permit check and cut lined up ahead of them.